Looking for:
Welcome to |
Yaesu ft60 manual.Yaesu FT-60 HT Quick Start Manual
Table Of Contents. Quick Links. See also: Technical Supplement , Quick Manual. Table of Contents. Previous Page. Next Page. Availability of accessories may vary. Some accessories are supplied as standard per local requirements, while others may be unavailable in some regions. Consult your Yaesu dealer for details regarding these and any newly-available options.
Connection of any non-Yaesu- approved accessory, should it cause damage, may void the Limited Warranty on this ap- paratus. Microphone The internal microphone is located here. Keypad These 16 keys select many of most important operating features on the FTR. The func- tions of the keys are described in detail on the pages to follow. FTR O See page 74 for details. Page Installation Of Accessories Open the Bat- tery Pack Latch on the bottom of the radio, then slide the battery downward and out from the radio while tilting the Belt Clip out of the way.
Page Battery Charging Please be advised that the NC may contribute noise to TV and radio reception in the immediate vicinity, so we do not recommend its use adjacent to such devices. Page Operation Hi! Page Selecting The Operating Band or scanning per the discussion in the next chapter.
Three basic frequency navigation methods are available on the FTR Page Transmission The scanner will stop when it receives a signal strong enough to break through the Squelch threshold. Press the PTT switch momentarily to cancel the scanning. These are the most basic steps; more advanced aspects of transmitter operation will be discussed later.
The possible lockout combi The reddish illumination yields clear viewing of the display in a dark environment, with mini- mal degradation of your night vision. Three options for activating the lamp are provided Page Rf Squelch 5. Press the PTT switch to save the new setting and return to normal operation.
Finally, rotate the SQL knob fully clockwise. Page Repeater Operation The FTR includes a number of features which make repeater operation simple and enjoyable. Your FTR has been configured, at the factory, for the repeater shifts customary in your country. See page This can help keep your radio quiet until a specific call is received, which may be helpful while operating in congested areas of the band.
Your repeater system may be configured for DCS; Page Tone Calling Hz Hz audio tone will be superimposed on the carrier. Once access to the repeater has been gained, you may release the MONI key, and use the PTT key for activating the transmitter thereafter. Page 29 The FTR provides a wide variety of memory system resources. Page Memory Mode 4. Page Deleting Memories The data will now have been copied to the VFO, although the original memory con- tents will remain intact on the previously-stored channel.
If a Split Frequency Memory channel was transferred, the TX frequency will be ignored you will be set up for Simplex operation on the Receive frequency. Page Memory Bank Operation The large number of memories available in the FTR could be difficult to utilize without some means of organizing them. Fortunately, the FTR includes provision for dividing the memories into as many as ten Memory Groups, so you can categorize the memories in a manner convenient to you.
See page 39 for details regarding activation of this mode. FTR O U. V Page Scanning The FTR allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station s on that frequency, if you like. Scanning operation is basically the same in each of the above modes.
Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal. Page Programmed Vfo Scan 7. If you want to change direction of the scan while it is underway, rotate the DIAL knob one click in the opposite direction in this case, one click counter-clockwise. If you watch This yields a long period of monitoring time, as no power will be consumed via audio output while scanning for the Alert Tone is in progress.
When the Memory Bank feature is activated, the FTR will check the lowest memory channel in the current Memory Bank as the priority channel.
When you have made your selection, press the PTT key to save the setting and exit to normal operation. You may also enable this feature band edge beeper to operate when the frequency reaches the band edge while tuning using the DIAL knob. This allows you to place a call to a specific station Paging , and to receive calls of your choice directed only to you Code Squelch. See page 25 for details. See page 29 for details on setting the Home channel. Page Smart Search Operation Smart Search is a great tool when visiting a city for the first time.
Page 52 Page 54 5. When you have made your selection, press the PTT switch to save the new setting and exit to normal operation. SET ] key to enter the Set mode. Page Cw Identifier Setup You may check your work by monitoring the entered callsign. To do this, repeat steps 1- 7 above, then press the MONI switch. SET ] key to enter the Set mode again. Besides numerical digits [ 0 ] through [ 9 ] , the keypad includes the [ ] and [ ] digits, plus the [ A ] , [ B ] , [ C ] , and [ D ] tones often used for repeater control.
See page 71 for details. When the password feature is activated, the radio will ask for the four digit password to be entered when the radio is first turned on. These may be changed by the user, if you wish to assign another Set Mode Item to either or both of these keys.
However, should an unusual operating situation arise in which you need to change between the available operating modes FM and AM , here is the proce- dure for doing so: 1. Page Mono Band Operation 2. Page Dcs Code Inversion 4. This can be particularly useful when configuring a number of transceivers for a public service opera- tion. It may be used for configuration of a wide variety of transceiver param- eters, some of which have not been detailed previously.
Use the following procedure to activate the Set Mode: 1. ON INT. Page 71 Enables or disables the VFO band edge limiting for the cur- rent band. KEY: The beeper sounds when you press any key. OFF: Beeper is disabled. Page 74 When the radio is set to the EMG. See page 44 for details. Available Values: PWD.
Available Values: RVT. OFF See page 42 for details. The receiver IF filter bandwidth is not changed via this setting. Available Values: ALT. Page Specifications Specifications are subject to change without notice, and are guaranteed within the and MHz amateur bands only.
Frequency ranges will vary according to transceiver version; check with your dealer. Page 83 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference including received, interference that may cause undesired operation.
All rights reserved. This manual is also suitable for: Fte. Print page 1 Print document 84 pages. Rename the bookmark. Delete bookmark? Cancel Delete.
Comments
Post a Comment